McIntosh Racing
Login myCart
March 29 2024 [New Zealand] 
Home   Blog   Company   Catalogue   Gallery   Forum   Tech docs   Members   Contact  

Catalogue

Models -> Featherbed -> Motor Parts
back to Featherbed
113-010 Manx Crankcases 500cc Short-stroke, cast in magnesium. Visually these crankcases are exactly the same as the original type with all casting numbers and details exactly as standard. The timing side crankcase wall is thicker than standard to give improved strength. $2,987.00
add to cart
113-020 Manx Crankcases 350cc Short-stroke. $2,987.00
add to cart
113-030 Manx Crankcases 500cc Long-stroke. $2,987.00
add to cart
113-060 Timing Cover - 1951-1963 Featherbed Models. 5 screw type. Cast in magnesium. $0.00
add to cart
113-070 Inner Timing Cover - 1951-1963 to suit all Featherbed models. Cast in magnesium. $0.00
add to cart
113-100 Carrillo Con-rod 500cc Short-stroke Manx. $703.00
add to cart
113-110 Carrillo Con-rod 350cc Short-stroke Manx. $703.00
add to cart
113-120 Carrillo Con-rod 500cc Long-stroke Manx. $740.00
add to cart
113-130 Carrillo Con-rod 350cc Long-stroke Manx. $703.00
add to cart
113-140 Carrillo Con-rod 500cc International. $703.00
add to cart
113-200 Cosworth Pistons 500cc Short-stroke 1960 3 ring type. 11:1.Comp. $520.00
add to cart
113-210 Cosworth Pistons 350cc Short-stroke 1960 3 ring type. 11:1.Comp. $520.00
add to cart
113-250 Arias Piston 79mm 500cc long stroke 14:1 alcohol. Will fit International or ES2 models. Can be machined to give approximately 9:1 compression ratio. Supplied with rings and gudgeon pin. $425.00
add to cart
113-260 Arias Piston 80mm 500cc long stroke. 14:1 alcohol. Will fit International or ES2 models. Can be machined to give approximately 9:1 compression ratio. Supplied with rings and gudgeon pin. $425.00
add to cart
113-270 Piston Rings for Arias 79mm or 80mm Long-stroke piston. $69.00
add to cart
113-280 Piston Rings to suit Norton Hepolite piston 350 Short-stroke. $76.00
add to cart
113-290 Piston Rings to suit Norton Hepolite piston 500 Short-stroke. $76.00
add to cart
113-291 Piston Rings to suit Norton Cosworth piston 500 Short-stroke. $0.00
add to cart
113-300 Woodruff Key to suit bevel and oil pump gear. 2 per set. $2.00
add to cart
113-310 Woodruff Key to suit long stroke drive sprocket. $7.00
add to cart
113-320 Woodruff Key to suit DOHC cambox central gear. $2.00
add to cart
113-340 Valve guide blank, bronze 5/16" ID $22.00
add to cart
113-341 Valve guide blank, bronze 11/32" ID $22.00
add to cart
113-342 Valve guide blank, bronze 3/8" ID $22.00
add to cart
113-343 Valve guide blank, cast iron 5/16" ID $14.00
add to cart
113-350 Titanium Inlet Valve. Oversize head, semi finished. Suitable for all models, allowing extra revs if required. 2/3rd weight of standard valves. $286.00
add to cart
113-355 Valve lash cap 5/16"x .060"thick $12.00
add to cart
113-355 Valve lash cap 11/32" $0.00
add to cart
113-355 Valve lash cap 3/8" $0.00
add to cart
113-352 Valve, stainless blank 1.600" $0.00
add to cart
113-353 Valve, stainless blank 1.880" $0.00
add to cart
113-360 Titanium Exhaust Valve. 11/32" stem, oversize head, semi finished. $279.00
add to cart
113-365 Valve keeper 5/16" $0.00
add to cart
113-366 Valve keeper 11/32" $0.00
add to cart
113-367 Valve keeper 3/8" $0.00
add to cart
113-380 Hairpin Valve Springs. DOHC Long-stroke Manx models. $196.00
add to cart
113-390 Hairpin Valve Springs. DOHC Short-stroke Manx models. $196.00
add to cart
113-400 Oil Quill Spring to suit big end feed. $7.00
add to cart
113-410 Oil Quill Spring to suit cambox feeds. $7.00
add to cart
113-450 Oil Pump to suit all International and Manx models. Oversize bronze body. To be machined to suit your crank case. Made with correct splined shafts. $696.00
add to cart
113-455 Oil Pump Drive Dog. 1932-1963. All OHC models. $36.00
add to cart
113-470 Crankshaft Nut -Timing Side L/H threaded nut to suit all Manx and International models. $38.00
add to cart
113-500 Crankshaft Assembly. Complete assembly made from chrome-moly steel heat treated to 80 tons UTS. With integral mainshafts. Uses Carrillo con-rod and modern INA caged roller big- end. Supplied balanced, assembled and trued. This is the finest crankshaft available for a Manx. $3,576.00
add to cart
113-510 Crankshaft Balancing- all models. Using the same method as the factory. Each wheel is balanced individually, stopping torsional vibration. Essential if piston or con-rod weight is changed from standard. $310.00
add to cart
113-520 Crankshaft Boring. To rebore crankpin holes for repair of damaged holes. Essential if flywheels will not true up to factory specifications. $0.00
add to cart
113-530 Assemble Crankshaft. To assemble flywheels and true. We can undertake to recondition your old crankshaft. $0.00
add to cart
113-550 Big End Assembly 1936-1960 500cc & 1948-1960. Made from the best quality materials and using modern type silver plated caged needle bearing. Available with oversize shoulders to give correct press fit in old flywheels. State size of flywheel holes when ordering. Correct interference fit is 0.0025". $395.00
add to cart
113-560 Big End Assembly 1961-1963 350cc and 500cc type. With eccentric bronze thrust washer and flange on side on con-rod liner. State size of flywheel holes when ordering. $435.00
add to cart
113-570 Big End Assembly 1932-1957 500cc International model. State size of flywheel holes when ordering. $395.00
add to cart
113-590 Crank-pin Nut hex type for all Long-stroke Manx models $74.00
add to cart
113-591 Crank-pin Nut hex type for all International models $74.00
add to cart
113-600 Cam Follower to suit all short stroke models. Made from through hardening steel and ground to correct radius. Complete with end-cap. $228.00
add to cart
113-610 Cam Follower to suit all long stroke DOHC models. Complete with end-cap. $228.00
add to cart
113-640 Cams SOHC to suit all International and Manx SOHC models. Latest type Manx grind. $222.00
add to cart
113-650 Cams to suit late model Short-stroke 500. $217.00
add to cart
113-660 Cams to suit all 500cc Long-stroke DOHC models. $228.00
add to cart
113-680 Magneto sprocket, top. Featherbed Manx $0.00
add to cart
113-681 Magneto sprocket, lower. Featherbed Manx $0.00
add to cart
113-700 Fins, large cast with correct taper and finish, to repair damaged cylinders and heads. $35.00
add to cart
113-701 Fins, small cast with correct taper and finish, to repair damaged cylinders and heads. $21.00
add to cart
113-710 Cylinder Head to suit all models 500cc Short-stroke Manx. Exact copy of original. State year required. $2,895.00
add to cart
113-720 Sponge - for hairpin springs. Helps keep oil loss under control. $10.00
add to cart
113-730 Inlet spacer, casting only. For 65mm stud centres. $46.00
add to cart
113-750 Valve Seat Repair. Correct fitting and seat cutting. $0.00
add to cart
113-760 Exhaust Thread Repair. All models. $170.00
add to cart
113-770 Cylinder Liner Repair. All models. We are able to repair worn or damaged cylinders to standard specifications. $0.00
add to cart
113-800 Main Bearing. Timing side. Double row ball type. For long-strokes and early short-strokes without 6 screw flanged bearing $286.00
add to cart
113-804 Main Bearing, oversize. Timing side. Double row ball type, ground to size to suit your case. $366.00
add to cart
113-805 Main Bearing, oversize. Timing side. Double row ball type, ground to size to suit your case. $366.00
add to cart
113-810 Main Bearing. Drive side. Lipped roller type to suit outer bearing of all Long-stroke Manx and International models. $167.00
add to cart
113-820 Main Bearing. Drive side. Roller type to suit all Manx models. 2 per set on Short-stroke models. 1 per long stroke and International models. $124.00
add to cart
113-830 Main Bearing - Special. Drive side assembly with one piece outer sleeve, 2 x roller bearings and thrust washer. For all Long-stroke Manx $332.00
add to cart
113-840 Top Bevel Gear Pair 1957-58 Course, "hunting-tooth" bevel for Oldham-coupling type vertical shaft motors. Can be used in all pre 1957 motors with modifications $585.00
add to cart
113-841 Bottom Bevel Gear Pair 1957-58 Course, "hunting-tooth" bevel for Oldham-coupling type vertical shaft motors. Can be used in all pre 1957 motors with modifications $585.00
add to cart
113-850 Vertical Shaft 'O' Ring for 1954-1958 type motors. Fits between head and cambox. $6.00
add to cart
113-860 Cam Box 'O' Rings 1954-1958 for all short stroke motors. Fits between head and cambox. $4.00
add to cart
113-870 Vertical Shaft Gland Nut 'O' Ring 1954-1958 for Short-stroke motors with chrome tube. Also used between head and barrel. $3.00
add to cart
113-880 Vertical Shaft Gland Nut 'O' Ring 1932-1958 for #113-891 or #113-892 modified gland nuts. To suit all International and long stroke Manx models. $3.00
add to cart
113-891 Vertical Shaft Gland Nut, Chrome, modified - 1932-1953. Special type, Chrome. With "O" ring seal. Also replaces perforated cup and locks ball bearing into housing. Original appearance. Recommended modification. Allows removal of cambox without undoing gland nuts. $72.00
add to cart
113-892 Vertical Shaft Gland Nut, Alloy, modified -1932-1953. Special type, Alloy. With "O" ring seal. Also replaces perforated cup, and locks ball bearing into housing. Original appearance. $88.00
add to cart
113-895 Gland nut copper washer replacement. Solid copper-plated washer replaces the original copper/asbestos washer to maintain original appearance. For use with modified gland nuts.  $11.00
add to cart
113-900 Cam drive Bearings. 1959-1963 Needle bearings for splined type vertical shaft. $52.00
add to cart
113-910 Cam drive Bearings. 1932-1953 Self-aligning ball bearings for all Oldham coupling vertical shaft motors. 2 per set. $223.00
add to cart
113-920 Cam drive Thrust Bearings. Needle roller thrust race for converting standard cam drive. Includes 2 x needle races and 4 x thrust washers. Recommended modification for splined type bevels. $37.00
add to cart
113-930 Dished Washer 1932-1957. Fits under lower self aligning bearing. Must be fitted to ensure no balls fall into bottom bevel gear. All Oldham coupling Manxes and Internationals. Can also be fitted under top bearing. $14.00
add to cart
113-940 Vertical Shaft Tube 1932-1953. Chrome. Original flanged type. To suit all International and long stroke Manx models. $52.00
add to cart
113-941 Vertical Shaft Tube, Modified 1932-1953. Plain type for use with #113-891 gland nuts. To suit all International and long stroke Manx models. $39.00
add to cart
113-950 Cambox Centre Shaft Ball Bearing, 1932-63 with groove for lock plate $56.00
add to cart
113-952 Cambox Centre Shaft Lipped Roller Bearing 1932-63 for magnesium cambox only. Can be uses in aluminium, cambox with an adaptor sleeve on outside diameter.  $158.00
add to cart
113-953 Cambox Centre Bearing Lock Plate, 1932-63. Improved type with smaller ID so plate can be punch-locked to stop bearing from rotating.  $31.00
add to cart

© 2005 copyright McIntosh Racing
website design : www.somethingwild.co.nz
7